Browse all practice questions for the NERC System Operator (SOS) Reliability Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

NERC System Operator (SOS) Reliability Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What should a transmission operator do if they observe a large power angle approaching 88 degrees between generation and load areas?
  • What should the Transmission Operator consider when reactive resources are limited?
  • Which action is appropriate when a 500 MW generator fails, causing system instability?
  • Which action transitions an Arranged Interchange to Confirmed Interchange status?
  • Who is responsible for developing and implementing load shedding plans?
  • Bulk Electric System facilities should not be removed from service unless which conditions are met?
  • A capacitor rated at 50 MVAR is supplying 45 MVARs to the system. What is the most likely reason for this situation?
  • What critical function does a System Operator perform regarding abnormal operating conditions?
  • What is the role of a Reliability Coordinator when a transmission operator reports an overload condition?
  • When adjusting voltage levels, what is a necessary consideration for stability during transmission?
  • Who is responsible for notifying entities when an Arranged Interchange transitions to a Confirmed Interchange?
  • What consequence arises from failing to meet the DCS criteria of recovery within 15 minutes?
  • When comparing the two lines connected to a bus, which factor is most critical in determining voltage behavior at the open ends?
  • To maximize effectiveness, where should reactive resources be located?
  • If an 800 MW generator trips in an external Balancing Authority, what would you likely observe in your area?
  • What happens to ACE if there is a frequency decline due to a loss of generation in an external balancing area?
  • Who should a Generator Operator notify if there are vibration problems leading to a reduction in reactive power production?
  • What should be used as benchmark loading conditions when scheduling maintenance for system reliability?
  • During a lightning storm, what should a Transmission Operator do after realizing possible cascading outages from a locked-out transmission line?
  • Which disturbance would be reportable for Disturbance Control Performance evaluation under NERC DCS criteria?
  • On a mild spring day, a transmission line trips. The line then trips again when energized. Which of the following is least likely to be the problem?
  • In coordinating under frequency load shedding, when should generators trip?
  • What action is required when a Transmission Operator makes significant changes to system operations?
  • Before shedding firm load to alleviate voltage collapse, whom must the operator confirm the action with?
  • What must a Balancing Authority do if voltage drops to 200 kV for 3 minutes after a generator trip?
  • What is the appropriate action for a Balancing Authority to restore an area after a blackout due to severe weather conditions?
  • Which equipment should be used first for maintaining or increasing system voltages?
  • Which type of power is essential for voltage support on loaded transmission lines and crucial for dynamic reserves?
  • What should an Operator do first if a transmission line is overloaded above its SOL?
  • What must be included in the considerations for scheduling arrangements in energy interchange?
  • Who must the Transmission Operator inform when an SOL has been exceeded?
  • What should a generator operator do while the voltage regulator is out of service for repairs?
  • If a Balancing Authority has a frequency bias and ACE equals 0, what should the interconnection ties equal?
  • Which of the following factors would not be considered in determining ratings of transmission facilities?
  • What actions can a Reliability Coordinator direct reliability entities within its area to take to restore system reliability?
  • What is the first action to take when an alarm indicates low oil pressure on a transmission cable?
  • Where should synchronization of islands occur in a power system?
  • What action should a Transmission Operator take after experiencing an unexpected loss of a transmission line with an upcoming peak demand?
  • During a slow time error correction, if the EMS system does not allow frequency changes, what is an appropriate response?
  • How does a Transmission Operator ensure the safe operation of the grid during unexpected system conditions?
  • What is one primary reason for operator involvement in protective schemes?
  • Which consequence is likely without adequate reactive power resources?
  • What is the correct response to a Balancing Authority experiencing all resources committed to firm load?
  • In a 345 kV transmission system, which device can be used to increase the voltage?
  • Who is the key point of contact during emergencies?
  • After declaring an NERC EEA Level 3, what is an effective tool to restore generation to load balance if load exceeds generation resources?
  • Interchange Schedules must begin and end at times agreed upon by which entities?
  • What operational practice must Transmission Operators follow regarding the handling of emergency situations?
  • What type of relay is a 51?
  • For a 345 kV line with a MW flow of 400 and a MVAR flow of 300, what is the MVA loading on the line?
  • 150 MW is flowing into the high side of a 200 MVA transformer. If the transformer windings have a 2 to 1 ratio, what MW value is flowing out of the low side winding of the transformer?
  • If a System Operator identifies a transmission line at 100% of its SOL, what action should be taken?
  • A report must be submitted to NERC after shedding how much firm load?
  • What is the purpose of a Special Protection System?
  • A 360 MW Interchange Transaction is curtailed to 0 MWs at 1540. What is the hourly integration for the hour ending at 1600?
  • What is the process of strategically placing generators to alter the flow of active and reactive power called?
  • If a step-down transformer has a 2 to 1 turn ratio and 140 MWs power is entering, what is the output power?
  • When should the Transmission Operator seek reactive power support?
  • What is the primary goal of Under Frequency Load Shedding (UFLS)?
  • What action should be taken if the system is approaching a high voltage alarm level?
  • What constitutes a reportable disturbance based on NERC DCS criteria for a Balancing Authority with a 900 MW unit?
  • If Line #2 is twice as long as Line #1 and Line #1 shows a higher voltage, what can you conclude about the voltage at the open end of Line #2?
  • What happens to the bus voltage when a long transmission line is connected from that bus and the other end is left open?
  • What mode should an asynchronously operating Balancing Authority switch its AGC to?
  • What is the loading on the shortest remaining line after one line trips, if initially loaded at 200 MW?
  • If a Transmission Operator cannot restore Real and/or Reactive Power Balance, what immediate action should be taken?
  • In the event of damaged transmission lines and tripped generators, what should the system operator do?
  • Which metered data is included in the calculation of Area Control Error (ACE)?
  • What is the primary responsibility of a Reliability Coordinator during system restoration?
  • If Balancing Authority A is importing 400 MWs from Balancing Authority B, what should they do to address the potential SOL issue?
  • Which entities can determine if a Dynamic Schedule deviation is a reliability concern?
  • A Transmission line is loaded at 125% of its System Operating Limit. What action would be acceptable under these conditions?
  • What action should the Reliability Coordinator coordinate if a real-time contingency analysis shows a high voltage transmission transformer overloading?
  • Which of the following would you expect to experience during a Geo-Magnetic disturbance?
  • What is the best course of action if a real-time contingency analysis shows a radial transmission line will overload?
  • Under what condition should the Reliability Coordinator use the Operating Procedure to open one end of the 161 kV line?
  • What is one of the key functions of under frequency load shedding?
  • Which of the following constitutes a reliability event?
  • What is the best course of action for a System Operator when faced with potential equipment failure on a transmission line?
  • What is typically monitored by the Reliability Coordinator during low-frequency events?
  • What is the most likely occurrence after a major transmission system disturbance causes a large loss of load?
  • How should a system operator respond if a 230 kV transmission line experiences an overload with specific MW and MVAR flows?
  • What is the main purpose of the Operating Plans developed by the Transmission Operator and Balancing Authority?
  • Which phenomenon can affect the voltage stability of a power system?
  • In system restoration, what should be the priority for restoring power?
  • What is the expected result when adjusting an under load tap changer (ULTC) tap setting to support low side voltage?
  • Which Energy Emergency Alert level is required if firm load shed is imminent?
  • If the actual frequency runs from 60.035 to 60.045, what does this indicate to a Balancing Authority Operator?
  • Which entity is responsible for initiating an Energy Emergency Alert?
  • What should the Balancing Authority do to handle a voltage drop resulting from a generator trip?
  • In the context of reliability, what best defines 'Frequency Error'?
  • How is Power Factor defined?
  • What is considered when determining the priority of load shedding during a frequency drop?
  • In an electrical system, when will voltage support equipment be most necessary?
  • Balancing Authorities on the Scheduling Path are responsible for assessing which aspects of the Interchange Transaction?
  • What values change instantaneously during a sudden loss of a large block of load?
  • In an over-capacitive system, what effect does a leading current sine wave have on voltage?
  • If a 50 MVA transformer has 30 MW's of load, how many MVARs can flow through the transformer?
  • Who must approve a Reliability Adjustment Arranged Interchange before it becomes Confirmed Interchange?
  • Who is responsible for notifying all parties when Interchange has transitioned to confirmed status?
  • What equipment is typically used to transform current from the primary circuit to a smaller proportional amount for protective relays?
  • Which factor can cause complications during system restoration?
  • Which relay would be engaged to protect against overcurrent conditions in a power system?
  • If the ACE is calculated using incorrect or incomplete data, what potential issue can arise during operations?
  • When is the ideal time to schedule a capacitor bank outage?
  • What is the purpose of having correct interchange schedules?
  • When two identical A/C generating units operate in parallel with different governor droops, which unit tends to take the lesser portion of load changes?
  • A conductor is rated for 180 MVA, a current transformer at one end is rated at 160 MVA, and the bus is rated at 200 MVA. What is the MVA limit for this transmission line?
  • As system loads increase, how must a System Operator respond effectively?
  • To keep inadvertent interchange down to a minimum, which action is the most effective?
  • What is the most common effect of a Geomagnetic Disturbance on the power system?
  • What indicators alert a system operator about potential voltage collapse on a heavy load day?
  • When should manual load reductions be executed according to the Operating Plan?
  • Who is responsible for updating the tag when a Dynamic Schedule varies significantly?
  • If a high voltage DC tie is on the Scheduling Path for a transaction, who shall coordinate the Interchange Schedule with the Transmission Operator of the HVDC tie?
  • Which is a primary function of a Balancing Authority during an emergency?
  • What is the risk of excessive MVAR supply during restoration attempts?
  • When a Transmission Operator is expecting to shed load due to an SOL, which parties must be notified?
  • When is the best time to schedule an outage for a 161 kV shunt capacitor bank for non-emergency work?
  • Who should notify the Sink Balancing Authority for a curtailed Interchange Transaction?
  • What term describes a situation where a Load-Serving Entity can no longer meet energy requirements?
  • What values must be monitored by a synchronous check relay before a circuit breaker can close automatically?
  • In a system restoration scenario, what is a critical factor that must be addressed regarding load?
  • Which of the following is NOT a requirement of the Reliability Coordinator concerning geomagnetic disturbances (GMDs)?
  • Which phrase describes the state of voltage collapse?
  • What is the role of a Regional Reliability Organization in response to system disturbances?
  • When a disturbance causes a frequency drop to 59.94 Hz, what should the Reliability Coordinator do first?
  • Who must have the authority to direct reliability entities to mitigate critical conditions?
  • What does an Operational Planning Analysis assess regarding planned operations for the next day?
  • What action should a Transmission Operator avoid when encountering high system loading?
  • All real-time system operators must monitor ___________.
  • If emergency resources are exhausted, what's the next step a system operator should take?
  • Who should a Generator Operator contact about issues with the generator voltage regulator?
  • The Reliability Coordinator shall identify sources of large _______________________ that may be contributing to Frequency Error, Time Error, or Inadvertent Interchange.
  • The 138/13 kV transformer was tripped to protect what from damage?
  • What should be done if the Interconnection frequency is 60.20 Hz and the ACE is a large positive value?
  • For which elements to be metered is essential for proper ACE equation functionality?
  • To effectively manage frequency during the restoration process, how much load should ideally be avoided from being energized?
  • What action should be taken when informed of a slow time error correction that cannot change the scheduled frequency?
  • What happens if the system voltage remains below .9 p.u. for an extended period?
  • What action is necessary when a Reliability Coordinator communicates an Operating Instruction?
  • What causes angle instability in a power system?
  • What must the Balancing Authorities do prior to implementing the Interchange Agreement with an HVDC Transmission Operator?
  • When experiencing multiple contingencies, at what interval should they be treated as a single contingency?
  • Under what condition should the Transmission Operator disconnect from the interconnection?
  • What type of relays are primarily used for power system equipment protection rather than line protection?
  • What should a Reliability Coordinator have in place if analysis tools are unavailable due to planned maintenance?
  • During peak hours, what is the appropriate notification to make when firm load shedding is necessary to prevent voltage collapse?
  • What happens to the transformer’s power when the voltage is reduced?
  • If a fault is indicated at Substation A and B, what does this suggest about the location of the fault?
  • What is an important measure when facing a disturbance in the power system?
  • What practice can mitigate the risk of excessive voltage increases during heavy loads?
  • In a Power System, cold load can best be described as which of the following?
  • What does a GMD refer to in the context of Reliability Coordinators?
  • If a Balancing Authority cannot meet demand and reserve requirements, which entity should it notify?
  • What typically occurs if system frequency drops significantly during operation?
  • When is voltage reduction for load relief acceptable on the transmission system?
  • Re-synchronization with the Interconnection is ideally performed at which type of location?
  • Why do system operators monitor system conditions closely?
  • What type of relay operates based on the ratio of potential transformer to current transformer measurements?
  • Which protective device calculates the impedance of a line by measuring the voltage and current of that line?
  • What is the primary goal of the Reliability Coordinator regarding interconnection reliability?
  • What must the transmission system operate to avoid due to the most severe single contingency?
  • During the restoration of a full system shutdown, what is the best practice to avoid re-collapsing the system?
  • How many MVars are gained when energizing a capacitor rated at 100 MVar on a 345 kV line at 90% of normal voltage?
  • What is the maximum block of load that can be restored to maintain frequency control with 600 MW of generation and 200 MW of spinning reserve?
  • What signifies an Emergency Energy Alert (EEA) Level 3?
  • Which type of transmission line is the best choice to energize a generator facility?
  • If a frequency bias setting is less negative than the response of a Balancing Authority during a frequency increase, what will be the ACE result?
  • What should a Reliability Coordinator do if a flow gate becomes overloaded due to a parallel line failure?
  • What alert level must a deficient entity request when all available resources are committed?
  • The Roxboro - Milburnie Black 230-kV line has 80 MW and 60 MVAR flowing into Milburnie Substation. What is the power factor?
  • What entity is responsible for taking corrective action after a tie line trip causes a thermal overload?
  • When a large block of load is lost, which error is expected to reflect that change?
  • What is the most critical factor for accurate load forecasting?
  • What action is required if system voltage drops below .87 p.u. for 10 minutes?
  • What impedance characteristic should system restoration plans establish to enhance the transmission system backbone?
  • To unload an overloaded radial transmission line, what action must the Transmission Operator take?
  • In an Arranged Interchange, who must receive the Arranged Interchange for reliability assessment?
  • Voltage reduction for load relief should primarily be made on which system?
  • Prior to installing new relays on major transmission tie lines, who should the Transmission Operator notify?
  • During which scenario is it essential for an operator to be aware of the interchange transactions prior to a system collapse?
  • A transformer rated at 50 MVA is currently carrying 30 MW of load. At this load, what is the maximum allowable MVAR flow through the transformer?
  • What action must a Transmission Operator take to unload an overloaded radial transmission line?
  • If a Transmission Operator recognizes potential reliability threats from line loading, what should they do?
  • When faced with a large generation trip, what should a Balancing Authority notify the Reliability Coordinator?
  • In preparations to synchronize two islands with differing frequencies, what action should be taken?
  • What resources should a system operator utilize to address emergency conditions?
  • Which type of relay acts as a safeguard for transmission lines?
  • Which of the following correctly describes the role of the Balancing Authority?
  • How much load needs to be shed for a 1 Hz frequency deviation when in an island?
  • What is an objective of voltage reduction during system stress?
  • What is the first action required to manage an SOL violation due to an overloaded flow gate?
  • What is a primary cause of low voltage levels in the Transmission and Distribution system?
  • What should a system operator prioritize to prevent cascading failures in the event of generator trips?
  • If a Balancing Area's ACE is initially -40 MW and loses 800 MW generation but stabilizes at -42 MW, what is the required action if it meets DCS?
  • What is a common strategy for managing reactive power during unexpected outages?
  • If a Balancing Authority has a Net Interchange Schedule of -250 MWs, what is the Balancing Authority's Inadvertent Interchange for a specified period based on actual interchange values?
  • What action should a transmission operator take when a major transmission line is overloaded and imminent damage is possible?
  • What is the definition of a contingency in power systems?
  • Before energizing a blacked-out area, a system operator must do which of the following?
  • When experiencing low voltages, what should Balancing Authority A do when Neighboring Balancing Authority B requests emergency assistance?
  • During system restoration, which strategy should be prioritized for effective load management?
  • What is a key factor for ensuring the reliability of a power system?
  • What does the term "Dynamic Schedule" refer to in the context of energy management?
  • System Operators must act to maintain reliability through actions like canceling outages and load shedding for which purpose?
  • Given an available transfer capability of 1200 MW, what is the maximum net interchange that can be scheduled from A to B considering other flows?
  • A System Operator has three generators online with 1200 MWs capacity and loads at 500 MWs. What is the max load they can restore without risking re-collapse?
  • Which relay type is specifically designed to prevent excessive current flow?
  • How many zones of protection do distance relay schemes often utilize?
  • In evaluating a line outage request, what must you ensure regarding contingencies?
  • What is the significance of a system's frequency bias setting in operations?
  • If reactive resources are limited, what should a Transmission Operator consider doing?
  • How can the operator verify synchronization before energizing an emerging power line?
  • What is the first action a Transmission Operator must take when energizing a blacked-out area?
  • Two phase conductors of a 138kV transmission line come in contact due to a storm, creating a phase to phase fault. What two measured parameters caused the distance relay to operate?
  • Entities that have a reliability relationship with a Reliability Coordinator must provide data to monitor operations of what?
  • Steady-State Stability occurs when which of the following conditions are present?
  • What is the relationship between the available transfer capability and the maximum scheduled interchange when dealing with unscheduled flows?
  • Given a system frequency of 60.00 Hz and a frequency bias setting of 100 MW/0.1 Hz, what is the ACE if the Net Actual Interchange is +100 MW?
  • What is typically a consequence of a major disturbance within a Balancing Authority?
  • To predict the system's near-term load pattern, which of the following is essential information for a system operator?
  • What must the Source Balancing Authority assess before approving Arranged Interchange?
  • Which entity integrates resource plans ahead of time and maintains load-interchange-generation balance within a Balancing Authority Area?
  • If the Source Balancing Authority denies a Reliability Adjustment Arranged Interchange due to reliability issues, what action must they take?
  • What occurs during reconfiguration when trying to offload heavily loaded lines?
  • What information is essential for the next-day analysis conducted by the Reliability Coordinator?
  • If a Balancing Authority is running low on resources, which Energy Emergency Alert Level should they request?
  • What action can be taken to prevent voltage collapse with insufficient reactive resources?
  • What term describes the loading on a transmission line when the MVAR supplied from the line's natural capacitance equals the MVAR needed to support its voltage?
  • If a circuit breaker lacks a synch-check and has a large standing phase angle, how should the operator confirm it is safe to close?
  • As load increases throughout the day, how do two adjacent lines, one overhead and one underground, respond?
  • What is the minimum expected recovery time for re-synchronizing after a generation trip?
  • The Reliability Coordinator shall coordinate what with other Reliability Coordinators as needed?
  • Which of the following best describes the consequence of allowing a power angle to exceed 90 degrees?
  • What should the Transmission Operator do when voltage levels at substation buses are below nominal after a trip?
  • After a frequency recovery, what is the total load a Transmission Operator must restore manually if the system frequency falls and subsequently returns to normal?
  • If a high voltage transmission line is scheduled for maintenance but other outages have occurred, what is the best course of action for the system operator?
  • What is defined as the collection of transmission assets that the Transmission Operator is responsible for operating?
  • What is the proper response regarding voltage control for a tied line crossing two Reliability Coordinators’ areas?
  • What does a positive ACE indicate when dealing with balancing authorities?
  • What is a key responsibility of the Balancing Authority regarding frequency control?
  • What is the net actual interchange for Balancing Authority B given its tie-line readings with BA A and BA C?
  • As a Transmission Operator, what device should you operate to raise the voltage level back to normal?
  • In what scenario might a Transmission Operator need to disconnect from the grid?
  • A portion of a Reliability Coordinator Area is experiencing declining voltage and is running short on reactive reserves. Which Operating Instruction should the Reliability Coordinator give?
  • The maximum and minimum voltage, current, frequency, real and reactive power flows on individual equipment are determined by which factor?
  • When implementing a system restoration plan, what should be the operator's first priority?
  • When generators are supplying reactive power, they are considered to be which of the following?
  • If a transmission line has a System Operating Limit (SOL) of 650 MWs and a firm transaction scheduled will load it to 665 MWs, how much of the non-firm transactions must be cut?
  • If substantial generation is offline due to issues, what action should not be taken until further reviewed?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy